Shure SLX14 System (WA302 Instrument Cable, SLX1 Wireless BodyPack Transmitter & SLX4 Diversity Receiver)
Performance Gear Wireless Systems feature Shure's patented Audio Refrence Companding for crystal-clear sound beyond the limits of conventional wireless technology.
Shure WA302 Instrument Cable
Instrument cable connects the T1, UT1, SC1, SLX1, LX1, ULX1, UC1 and U1 body-pack transmitter to a guitar or other instrument. Features a 2.5 foot (.75m), length with 1/4-inch plug and 4-pin mini connector (TA4F) (supplied with instrument systems).
Cable, Instrument, 2.5 foot (.75 m), 4 Pin Mini Connector (TA4F) to 1/4-inch Connector, used with T1, SC1, LX1, SLX1, U1, UC1 ULX1 and UT1 Bodypack Transmitters
Shure SLX1 Wireless Bodypack Transmitter
The SLX1 bodypack transmitter is designed to hold up to the most adverse conditions. Whether used with headworn, lavalier, instrument microphones, or with guitars or basses, the SLX1 is the definition of reliability.
Backlit LCD with timeout feature, Frequency and power lockout, and 3-segment battery fuel gauge
SLX Wireless Systems feature Shure's patented Audio Reference Companding for crystal-clear sound beyond the limits of conventional wireless technology.
- Automatic Transmitter Setup
- Backlit LCD with timeout feature
- Frequency and power lockout
- 3-segment battery fuel gauge
- 2 AA batteries (included) provide 8 hours of continuous use
- 518 - 782 MHz operating range
SLX4 Diversity Receiver, The SLX4 receiver bring unprecedented ease of use to wireless with Automatic Frequency Selection and Automatic Transmitter Setup. With included rack hardware and detachable antennas, it is ready for immediate installation right out of the box.
SLX Wireless Systems feature Shure's patented Audio Reference Companding for crystal-clear sound beyond the limits of conventional wireless technology.
Features
- Automatic Frequency Selection
- Automatic Transmitter Setup
- 960 Selectable frequencies across 24 MHz bandwidth
- Selectable frequencies in 25 kHz steps
- Detachable 1/4 wave antennas
- Microprocessor-controlled predictive diversity
- RF presence LED
- 5-segment audio meter
- Multi-function, backlit LCD
- Low battery indicator
- Frequency and power lockout
- Rugged metal chassis
- Volume control on rear of unit
- 1/2 rack design
- Furnished rack hardware
- Non-slip bumpers for use out of rack
- XLR and 1/4" outputs
Specification
Dimensions: 42 mm H x 197 mm W x 134 mm D (1.65 x 7.76 x 5.28 in.)
Weight : 816 g (1 lb. 13 oz.)
Housing : Galvanized steel
Audio Output Level: (ref. +/– 38 kHz deviation with 1 kHz tone)
- XLR connector (into 600 O load): –13 dBV
- 1/4 inch connector (into 3000 O load): –2 dBV
Output Impedance :
- XLR connector: 200 O
- 1/4 inch connector: 1kO
XLR output :
Impedance balanced
- Pin 1: Ground
- Pin 2: (+)
- Pin 3: (-)
Sensitivity : –105 dBm for 12 dB SINAD, typical
Image Rejection : >70 dB, typical
Power Requirements : 12–18 Vdc at 150 mA, supplied by external power supply
Operating Range Under Typical Conditions : 100m (300 ft.) Note: Actual range depends on RF signal absorption, reflection, and interference
Audio Frequency Response (+/– 2 dB): Minimum: 45 Hz, Maximum: 15 kHz, Note: Overall system frequency depends on microphone element.
Total Harmonic Distortion (ref. +/– 38 kHz deviation, 1 kHz tone): 0.5%, typical
Dynamic Range : >100 dB A-weighted
Operating Temperature Range : –18°C (0°F) to +50°C (+122°F), Note: battery characteristics may limit this range
Transmitter Audio Polarity : Positive pressure on microphone diaphragm (or positive voltage applied to tip of WA302 phone plug) produces positive voltage on pin 2 (with respect to pin 3 of low impedance output) and the tip of the high impedance 1/4-inch output.
