NJD SPECTRE COLOUR MIXING FLOODLIGHT

An amazing new concept in stage lighting, the SPECTRE provides the user with an almost limitless choice of colours by mixing three 500 Watt lamps, one red, one green and one blue through dichroic filters. The internal microprocessor interpret the users requirements and calculate what percentage of each colour is needed to create the colour wash desired.
From vivid prime colours to gentle pastels the spectre can create them all and with no moving colour wheels or scrolls the colour change viewed by the audience is absolutely seamless.

Control is simplicity itself via. either DMX, 0-10 Volts or MIDI, all that is required is three channels. Channel one is a dimmer which controls the brightness from 0 - 100%. Channel two controls the colour selection, moving the slider through 0 -100% gently taking the colours through 12 colours and all intermediate shades. Channel three allows the operator to choose any pastel of a selected colour (e.g. If channel 2 in set to red then channel 3 will allow all pastels from solid red to a hint of pink). For connection leads see our section on "Equipment leads" RJ45, RJ12 and DMX XLR leads

Specification

• Lamp : 3 x A1/244 (230V 500W) 
• Lamp life switch : High brightness / extended life
• Colours : 65,536 continuously variable
• Connection : Inlet IEC input connector
• DMX : 5-pin male/female XLR or RJ45 (Includes 5V supply for remote control)
• 0 - 10V Analogue : 7-pin DIN (Includes 15V supply for FADE 4 etc.)
• MIDI : 5-pin Din (in and out)
• Cooling : Temperature controlled fan
• Fuse : F10A
• Dimensions : 250mm x 220mm x 220mm
• Weight : 5.4kg

A1/244 240V 500W (GY9.5) 7389 LAMP

S-PEDAL,Foot Operated Lighting Controller

S-PEDAL

• Foot operated lighting controller
• Robust extruded aluminium case
• DMX output
• Sound Chaser
• Trigger from MIDI drum Track
• Flood in any colour 2 storable scenes including "Blackout"
• Can control up to 32 NJD ColourMixing Floodlights

S-PEDAL
TECHNICAL SPECIFICATION
Audio input sensitivity : 1.5V rms to 50V
Audio input impedance : 33k Ohms
Audio input connector : 6.35mm Mono Jack
Output connectors :5 pin XLR
Output : DMX512 : 1990    80 Channels
Power requirements : 12V DC 50mA
Power supply connector: 2.5mm DC power socket
Dimensions : 405mm x 201mm  x 58mm
Weight : 3.1kg

NOTE: POWER SUPPLY REQUIREMENTS
For NJD products fitted with 5 pin XLR sockets or the Mirage with terminal block connections, NO EXTERNAL POWER SUPPLY IS REQUIRED. For NJD products fitted with 3 pin XLR or Jack Socket connectors AN EXTERNAL 12V DC 50mA POWER SUPPLY IS REQUIRED (Not supplied)   SEE P006DN.

XLR DMX Cable, Digital signal cable: A range of digital AES-EBU, 100 ohm cables for DMX512 lighting and other digital signal applications where low signal distortion is required. Cables are black and wired with all circuits wired.

NJD SFC1 REMOTE FOR SPECTRE (Lead Not Included) This hand held controller gives the user control over the brightness of the Spectre ranging from 0% to 100%. The colour is selectable as is the shade again from the brightest shade down through all the pastel shades to white. Programs are also built in the unit to operate chase fade, colour chase, colour fade, random and blend programs as is the speed of these programs. Colour scrolling can also be acheived using the SFC1. Also a microphone is built into the unit for sound activation. An RJ45 or RJ12 (see options below) terminated lead is all that is required to connect this remote to the Spectre. This unit had no power supply taking it's power via the lead from the Spectre.
RJ45 & RJ12 Leads are listed in the Equipment leads section.

DMX RJ45 Cable, Cat 5 patch cable. This DMX cable has moulded strain relief which allow them to be plugged into appliance sockets ect, without the strain relief fouling the equipment. Cables are blue and wired with all circuits wired.CAT 5 to CAT 5UTP