£90.50 (£108.60 Including VAT at 20%)

Cloud CDR-1 Remote Control Module, for music source, level and grouping (user mode). The CDR-1 is a remote control unit specifically designed for use with the DCM-1.

CDR-1s may be fitted to standard electrical back boxes in whatever location is convenient in each zone.Any zone may have one CDR-1, more than one, or none at all.The DCM-1 can support up to 100 CDR-1s. CDR-1s are interconnected with just one standard CAT-5 UTP cable; units may be daisy-chained at will and/or connected individually back to the DCM-1’s four CDR ports using almost any wiring topology convenient for the installation.

The DCM-1’s own PSU has the capacity to power up to 8 CDR 1s directly, via the CAT-5 connections. Systems requiring more than 8 CDR-1s will need additional power supplies, whose location and system connection will depend on the topology and cable lengths involved. Full details are provided with each CDR-1.

The CDR-1 provides the user with local source selection and level control for the zone in which it is fitted. It additionally allows selection of any zone groups to which the zone has been assigned, which gives simple and complete control over audio in multiple areas which may be split or joined in different ways at different times.

Once enabled on the DCM-1 and a local key code entered, zone EQ is also adjustable from the CDR-1, allowing audio optimisation from within the zone itself.An Installer Mode permits zone assignment and adjustment of other installation parameters.

£69.75 (£83.70 Including VAT at 20%)

Cloud PM1 Paging Microphone, Single Zone Paging Microphone - Push to Talk

£89.65 (£107.58 Including VAT at 20%)

Cloud ME-1 Active Input Plate with Dual Mic Input, Mic level control and 2 band EQ, The ME-1 input connector plate provides two balanced microphone inputs, and is useful in multi-purpose areas where mics are sometimes needed.The ME-1 has adjustable mic level and EQ per input, and connects to one of the DCM-1’s four dedicated Mic Inputs with single screened CAT-5 cable.The ME-1’s two inputs are mixed together at the plate, and the summed mic signal applied to the DCM-1.

Any of the DCM-1’s mic inputs can be routed to any zone without restriction.

Inputs on the ME-1 are via latching 3-pin female XLR connectors. 12v phantom power is available on either input if required (set via a jumper accessible from the rear plate).

£78.57 (£94.28 Including VAT at 20%)

Cloud BE-1 Active Input Plate with 2 Balanced Female XLR Inputs, The BE-1 is an input connector plate of similar type to the LE-1. It provides a stereo balanced line-level input, permitting professional audio equipment such as mixing consoles, DI boxes or broadcast equipment to be connected. Like the LE-1, it connects to one of the DCM-1’s Extension Ports with a single screened CAT-5 cable.

BE-1s may be daisy-chained in the same way as LE-1s, and the two types of plate may be intermixed.

Two industry-standard latching 3-pin female XLR connectors are fitted.

Once connected, any audio connected to the BE-1 is treated as any other source and can be routed to any zone in the same manner.

£89.65 (£107.58 Including VAT at 20%)

Cloud LE-1 Active Input Plate with 1 Stereo Line Input (phono and 3.5mm jack socket), The LE-1 is an input connector plate which can be installed wherever required. Versions are available to fit standard UK, US or Australian dual-gang electrical back boxes. It allows connection of a stereo unbalanced line-level audio source, such as a portable music centre, laptop, radio mic receiver or similar, and connects to one of the DCM-1’s Extension Ports with a single screened CAT-5 cable.

Multiple LE-1s may be “daisy-chained” together to provide input points at different locations in the same zone. Signals applied to plates wired in this way will be summed together.An internal gating circuit on each plate automatically “disconnects” any chained plates which are not in use, to minimise noise contribution.

The LE-1’s inputs are electronically buffered to minimise noise and interference pickup, and input gain is locally adjustable with a preset control.Two types of input connector are provided for user convenience: dual phono sockets and a 3.5mm stereo jack socket; ±12dB of gain trim adjustment is available on the faceplate.

Once connected, any audio connected to an LE-1 is treated as any other source and can be routed to any zone in the same manner.

£187.48 (£224.98 Including VAT at 20%)

The Cloud PM4 Paging Microphones are designed for general purpose multizone applications and can also be used with non-Cloud products.  The Cloud PM range’s features:   Individual and multiple zone selection, Definable zone groups with group selection, Pre-announcement chime with internal chime sounder, TALK and CALL ALL buttons, BUSY L.E.D, Configurable two-layer announcement priority system, Auto-zone reset after announcement, Zone disable function. 

Please note:  The Cloud PM is designed to interface directly with recent Cloud products - such as the DCM-1 - via the Cloud Digital Paging Interface, which uses standard CAT-5 cable and RJ45 connectors. It may also be used with any other audio system equipped with ‘short-toground’ paging access for selecting the zone(s) to be paged. This includes the following current* Cloud products: • Z4ii and Z8ii Venue Mixers • CX163 and CX263 Mixers • 36/50 and 46/50 Integrated Mixer Amplifiers • Other, older Cloud products may also be compatible; Multiple PMs may be interconnected (via the Digital Paging Interface) to permit paging from more than one location. A total cable run of up 1 km is permissible, with a maximum of 32 PM units. Different models of PM may be intermixed on a single network. It is also possible to configure a PM to address only a subset of the available zones. The PM is also compatible with the older Cloud CDPM range of digital paging microphones. PM microphones and CDPM microphones may be freely intermixed on the Digital Paging Interface.

Technical Specifications

• Up to sixteen Zones are available in an installation.
• All PMs are fitted with sixteen access terminal so that any PM can be used as the mixer interface in a multiple PM system 
• PM4 Four zones: Can interface upto sixteen zones from linked PMs.

 Features 

• Pre announcement chime:  Choice of four chimes selected by internal jumper. Chime can be set off/on by internal jumper. Internal sounder. Can be set off/on by internal jumper. Chime Level control preset.
• Interconnectable:  PMs of any combination of zone sizes can be daisy chained using CAT5 cable 
• Bank shift:  A PMs pageable zones can be shifted around the available sixteen zones. Set by internal jumpers.
• Zone barring: A PM can be barred from accessing zones. Set by internal jumper 
• Group lock:  The group buttons can be locked to prevent tampering. Set by internal jumper.
• Priority:  A PM can be set to high priority enabling it to interrupt a low priority PM. Set by internal jumper.
• Microphone level Preset allows a PMs level to be trimmed Auto zone reset Allows a zone selection to be retained after a page. Set by internal jumper.

Performance:

• Directivity:  Unidirectional, cardioid pattern
• Microphone element:  Electret condensor
• Sensitivity (1KHz) 68 dB ± 3 dB ( 0 dB=1V/ μbar 1KHz indicated by open circuit)
• Frequency response 80 Hz ~ 16,000Hz 
• Internal compressor 

Controls - Elastomer push buttonswith SMD tact switches 

• Zone:  Select a zone for paging.
• Zone Light:  Indicates a zones selection.
• Clear:  Clear all selected zones 
• Talk:  Open a call to selected zones.
• Call all: Open a call to all zones available to the PM.
• Group:  Four group buttons give programmable zone selection.
• Busy Light:  Indicates when paging system is in use 

Connections 

• Analogue Use with traditional short to ground mixers.
• Microphone: Internal three poles screw terminal. Hot, cold and screen.
• Access Internal sixteen poles screw terminal allows any model of PM to interface the full sixteen zones available to an installation 
• Digital:  Use to interconnect PMs or interface to digital enabled mixers such as the Cloud DCM-1.
• RJ45 OUT:  Carries switching data and transmits analogue audio to the next daisy chained unit or mixer. Also receives power when connected to a mixer 
• RJ45 IN:  Carries switching data and receives analogue audio from other PMs. 
• Power Internal two poles screw terminal. Power from mixer via access cable 2.1mm concentric power jack.
• Use an external PSU RJ45 OUT socket Power from mixer via CAT5 cable Power - VoltageInternal screw terminal 12 -24VDC External. 
• 2.1mm jack 12 - 24VDC, 9-17VAC. 
• RJ45 OUT socket 12 -15VDC from mixer.
• Power - Consumption PM4 55mA, 

Physical Dimension

• Width 245mm Height (not including gooseneck) 65mm Depth 170mm Gooseneck 300mm .
• Weight 1.2kg 

Physical Finish 

• Cabinet Black rubberised ABS Base Slate grey painted steel Gooseneck.
• Black painted brass.
• Mounting Rubber feet.

Cables -Analogue 

• Audio Twin core screened (Microphone cable). 
• Access Screened multicore. 1 core per zone, 1 core for ground, plus 1 core for power if powered by mixer Maximum length 100m.
• Cables - Digital Type Cat 5 Maximum length 1km total.
• Maximum connected PMS 32

£217.30 (£260.76 Including VAT at 20%)

The Cloud PM8 Paging Microphones are designed for general purpose multizone applications and can also be used with non-Cloud products.  The Cloud PM range’s features:   Individual and multiple zone selection, Definable zone groups with group selection, Pre-announcement chime with internal chime sounder, TALK and CALL ALL buttons, BUSY L.E.D, Configurable two-layer announcement priority system, Auto-zone reset after announcement, Zone disable function. 

Please note:  The Cloud PM 8 is designed to interface directly with recent Cloud products - such as the DCM-1 - via the Cloud Digital Paging Interface, which uses standard CAT-5 cable and RJ45 connectors. It may also be used with any other audio system equipped with ‘short-toground’ paging access for selecting the zone(s) to be paged. This includes the following current* Cloud products: • Z4ii and Z8ii Venue Mixers • CX163 and CX263 Mixers • 36/50 and 46/50 Integrated Mixer Amplifiers • Other, older Cloud products may also be compatible; Multiple PMs may be interconnected (via the Digital Paging Interface) to permit paging from more than one location. A total cable run of up 1 km is permissible, with a maximum of 32 PM units. Different models of PM may be intermixed on a single network. It is also possible to configure a PM to address only a subset of the available zones. The PM is also compatible with the older Cloud CDPM range of digital paging microphones. PM microphones and CDPM microphones may be freely intermixed on the Digital Paging Interface.

Technical Specifications

• Up to sixteen Zones are available in an installation.
• All PMs are fitted with sixteen access terminal so that any PM can be used as the mixer interface in a multiple PM system 
• PM8 Eight zones: Can interface upto sixteen zones from linked PMs

 Features 

• Pre announcement chime:  Choice of four chimes selected by internal jumper. Chime can be set off/on by internal jumper. Internal sounder. Can be set off/on by internal jumper. Chime Level control preset.
• Interconnectable:  PMs of any combination of zone sizes can be daisy chained using CAT5 cable 
• Bank shift:  A PMs pageable zones can be shifted around the available sixteen zones. Set by internal jumpers.
• Zone barring: A PM can be barred from accessing zones. Set by internal jumper 
• Group lock:  The group buttons can be locked to prevent tampering. Set by internal jumper.
• Priority:  A PM can be set to high priority enabling it to interrupt a low priority PM. Set by internal jumper.
• Microphone level Preset allows a PMs level to be trimmed Auto zone reset Allows a zone selection to be retained after a page. Set by internal jumper.

Performance:

• Directivity:  Unidirectional, cardioid pattern
• Microphone element:  Electret condensor
• Sensitivity (1KHz) 68 dB ± 3 dB ( 0 dB=1V/ μbar 1KHz indicated by open circuit)
• Frequency response 80 Hz ~ 16,000Hz 
• Internal compressor 

Controls - Elastomer push buttonswith SMD tact switches 

• Zone:  Select a zone for paging.
• Zone Light:  Indicates a zones selection.
• Clear:  Clear all selected zones 
• Talk:  Open a call to selected zones.
• Call all: Open a call to all zones available to the PM.
• Group:  Four group buttons give programmable zone selection.
• Busy Light:  Indicates when paging system is in use 

Connections 

• Analogue Use with traditional short to ground mixers.
• Microphone: Internal three poles screw terminal. Hot, cold and screen.
• Access Internal sixteen poles screw terminal allows any model of PM to interface the full sixteen zones available to an installation 
• Digital:  Use to interconnect PMs or interface to digital enabled mixers such as the Cloud DCM-1.
• RJ45 OUT:  Carries switching data and transmits analogue audio to the next daisy chained unit or mixer. Also receives power when connected to a mixer 
• RJ45 IN:  Carries switching data and receives analogue audio from other PMs. 
• Power Internal two poles screw terminal. Power from mixer via access cable 2.1mm concentric power jack.
• Use an external PSU RJ45 OUT socket Power from mixer via CAT5 cable Power - VoltageInternal screw terminal 12 -24VDC External. 
• 2.1mm jack 12 - 24VDC, 9-17VAC. 
• RJ45 OUT socket 12 -15VDC from mixer.
• Power - Consumption PM8 61mA,

Physical Dimension

• Width 245mm Height (not including gooseneck) 65mm Depth 170mm Gooseneck 300mm .
• Weight 1.2kg 

Physical Finish 

• Cabinet Black rubberised ABS Base Slate grey painted steel Gooseneck.
• Black painted brass.
• Mounting Rubber feet.

Cables -Analogue 

• Audio Twin core screened (Microphone cable). 
• Access Screened multicore. 1 core per zone, 1 core for ground, plus 1 core for power if powered by mixer Maximum length 100m.
• Cables - Digital Type Cat 5 Maximum length 1km total.
• Maximum connected PMS 32

£234.34 (£281.21 Including VAT at 20%)

The Cloud PM12 Paging Microphones are designed for general purpose multizone applications and can also be used with non-Cloud products.  The Cloud PM range’s features:   Individual and multiple zone selection, Definable zone groups with group selection, Pre-announcement chime with internal chime sounder, TALK and CALL ALL buttons, BUSY L.E.D, Configurable two-layer announcement priority system, Auto-zone reset after announcement, Zone disable function. 

Please note:  The Cloud PM 12 is designed to interface directly with recent Cloud products - such as the DCM-1 - via the Cloud Digital Paging Interface, which uses standard CAT-5 cable and RJ45 connectors. It may also be used with any other audio system equipped with ‘short-toground’ paging access for selecting the zone(s) to be paged. This includes the following current* Cloud products: • Z4ii and Z8ii Venue Mixers • CX163 and CX263 Mixers • 36/50 and 46/50 Integrated Mixer Amplifiers • Other, older Cloud products may also be compatible; Multiple PMs may be interconnected (via the Digital Paging Interface) to permit paging from more than one location. A total cable run of up 1 km is permissible, with a maximum of 32 PM units. Different models of PM may be intermixed on a single network. It is also possible to configure a PM to address only a subset of the available zones. The PM is also compatible with the older Cloud CDPM range of digital paging microphones. PM microphones and CDPM microphones may be freely intermixed on the Digital Paging Interface.

Technical Specifications

• Up to sixteen Zones are available in an installation.
• All PMs are fitted with sixteen access terminal so that any PM can be used as the mixer interface in a multiple PM system 
• PM12 Twelve zones : Can interface upto sixteen zones from linked PMs 

 Features 

• Pre announcement chime:  Choice of four chimes selected by internal jumper. Chime can be set off/on by internal jumper. Internal sounder. Can be set off/on by internal jumper. Chime Level control preset.
• Interconnectable:  PMs of any combination of zone sizes can be daisy chained using CAT5 cable 
• Bank shift:  A PMs pageable zones can be shifted around the available sixteen zones. Set by internal jumpers.
• Zone barring: A PM can be barred from accessing zones. Set by internal jumper 
• Group lock:  The group buttons can be locked to prevent tampering. Set by internal jumper.
• Priority:  A PM can be set to high priority enabling it to interrupt a low priority PM. Set by internal jumper.
• Microphone level Preset allows a PMs level to be trimmed Auto zone reset Allows a zone selection to be retained after a page. Set by internal jumper.

Performance:

• Directivity:  Unidirectional, cardioid pattern
• Microphone element:  Electret condensor
• Sensitivity (1KHz) 68 dB ± 3 dB ( 0 dB=1V/ μbar 1KHz indicated by open circuit)
• Frequency response 80 Hz ~ 16,000Hz 
• Internal compressor 

Controls - Elastomer push buttonswith SMD tact switches 

• Zone:  Select a zone for paging.
• Zone Light:  Indicates a zones selection.
• Clear:  Clear all selected zones 
• Talk:  Open a call to selected zones.
• Call all: Open a call to all zones available to the PM.
• Group:  Four group buttons give programmable zone selection.
• Busy Light:  Indicates when paging system is in use 

Connections 

• Analogue Use with traditional short to ground mixers.
• Microphone: Internal three poles screw terminal. Hot, cold and screen.
• Access Internal sixteen poles screw terminal allows any model of PM to interface the full sixteen zones available to an installation 
• Digital:  Use to interconnect PMs or interface to digital enabled mixers such as the Cloud DCM-1.
• RJ45 OUT:  Carries switching data and transmits analogue audio to the next daisy chained unit or mixer. Also receives power when connected to a mixer 
• RJ45 IN:  Carries switching data and receives analogue audio from other PMs. 
• Power Internal two poles screw terminal. Power from mixer via access cable 2.1mm concentric power jack.
• Use an external PSU RJ45 OUT socket Power from mixer via CAT5 cable Power - VoltageInternal screw terminal 12 -24VDC External. 
• 2.1mm jack 12 - 24VDC, 9-17VAC. 
• RJ45 OUT socket 12 -15VDC from mixer.
• Power - Consumption PM12 67mA.

Physical Dimension

• Width 245mm Height (not including gooseneck) 65mm Depth 170mm Gooseneck 300mm .
• Weight 1.2kg 

Physical Finish 

• Cabinet Black rubberised ABS Base Slate grey painted steel Gooseneck.
• Black painted brass.
• Mounting Rubber feet.

Cables -Analogue 

• Audio Twin core screened (Microphone cable). 
• Access Screened multicore. 1 core per zone, 1 core for ground, plus 1 core for power if powered by mixer Maximum length 100m.
• Cables - Digital Type Cat 5 Maximum length 1km total.
• Maximum connected PMS 32

£251.38 (£301.66 Including VAT at 20%)

The Cloud PM16 Paging Microphones are designed for general purpose multizone applications and can also be used with non-Cloud products.  The Cloud PM range’s features:   Individual and multiple zone selection, Definable zone groups with group selection, Pre-announcement chime with internal chime sounder, TALK and CALL ALL buttons, BUSY L.E.D, Configurable two-layer announcement priority system, Auto-zone reset after announcement, Zone disable function. 

Please note:  The Cloud PM is designed to interface directly with recent Cloud products - such as the DCM-1 - via the Cloud Digital Paging Interface, which uses standard CAT-5 cable and RJ45 connectors. It may also be used with any other audio system equipped with ‘short-toground’ paging access for selecting the zone(s) to be paged. This includes the following current* Cloud products: • Z4ii and Z8ii Venue Mixers • CX163 and CX263 Mixers • 36/50 and 46/50 Integrated Mixer Amplifiers • Other, older Cloud products may also be compatible; Multiple PMs may be interconnected (via the Digital Paging Interface) to permit paging from more than one location. A total cable run of up 1 km is permissible, with a maximum of 32 PM units. Different models of PM may be intermixed on a single network. It is also possible to configure a PM to address only a subset of the available zones. The PM is also compatible with the older Cloud CDPM range of digital paging microphones. PM microphones and CDPM microphones may be freely intermixed on the Digital Paging Interface.

Technical Specifications

• Up to sixteen Zones are available in an installation.
• All PMs are fitted with sixteen access terminal so that any PM can be used as the mixer interface in a multiple PM system 
• PM16 Sixteen Zones:

 Features 

• Pre announcement chime:  Choice of four chimes selected by internal jumper. Chime can be set off/on by internal jumper. Internal sounder. Can be set off/on by internal jumper. Chime Level control preset.
• Interconnectable:  PMs of any combination of zone sizes can be daisy chained using CAT5 cable 
• Bank shift:  A PMs pageable zones can be shifted around the available sixteen zones. Set by internal jumpers.
• Zone barring: A PM can be barred from accessing zones. Set by internal jumper 
• Group lock:  The group buttons can be locked to prevent tampering. Set by internal jumper.
• Priority:  A PM can be set to high priority enabling it to interrupt a low priority PM. Set by internal jumper.
• Microphone level Preset allows a PMs level to be trimmed Auto zone reset Allows a zone selection to be retained after a page. Set by internal jumper.

Performance:

• Directivity:  Unidirectional, cardioid pattern
• Microphone element:  Electret condensor
• Sensitivity (1KHz) 68 dB ± 3 dB ( 0 dB=1V/ μbar 1KHz indicated by open circuit)
• Frequency response 80 Hz ~ 16,000Hz 
• Internal compressor 

Controls - Elastomer push buttonswith SMD tact switches 

• Zone:  Select a zone for paging.
• Zone Light:  Indicates a zones selection.
• Clear:  Clear all selected zones 
• Talk:  Open a call to selected zones.
• Call all: Open a call to all zones available to the PM.
• Group:  Four group buttons give programmable zone selection.
• Busy Light:  Indicates when paging system is in use 

Connections 

• Analogue Use with traditional short to ground mixers.
• Microphone: Internal three poles screw terminal. Hot, cold and screen.
• Access Internal sixteen poles screw terminal allows any model of PM to interface the full sixteen zones available to an installation 
• Digital:  Use to interconnect PMs or interface to digital enabled mixers such as the Cloud DCM-1.
• RJ45 OUT:  Carries switching data and transmits analogue audio to the next daisy chained unit or mixer. Also receives power when connected to a mixer 
• RJ45 IN:  Carries switching data and receives analogue audio from other PMs. 
• Power Internal two poles screw terminal. Power from mixer via access cable 2.1mm concentric power jack.
• Use an external PSU RJ45 OUT socket Power from mixer via CAT5 cable Power - VoltageInternal screw terminal 12 -24VDC External. 
• 2.1mm jack 12 - 24VDC, 9-17VAC. 
• RJ45 OUT socket 12 -15VDC from mixer.
• Power - Consumption:  PM16 73mA .

Physical Dimension

• Width 245mm Height (not including gooseneck) 65mm Depth 170mm Gooseneck 300mm .
• Weight 1.2kg 

Physical Finish 

• Cabinet Black rubberised ABS Base Slate grey painted steel Gooseneck.
• Black painted brass.
• Mounting Rubber feet.

Cables -Analogue 

• Audio Twin core screened (Microphone cable). 
• Access Screened multicore. 1 core per zone, 1 core for ground, plus 1 core for power if powered by mixer Maximum length 100m.
• Cables - Digital Type Cat 5 Maximum length 1km total.
• Maximum connected PMS 32